10 years of experience in composite curing ovens

Our composite curing ovens are adapted to your various processes of composite manufacturing: prepreg, RTM, infusion, filament wiring, winding, honeycomb drying, moulds (pre)heating, injection of resin under vacuum in moulds, polymerization (under vacuum), curing, post-curing, prototyping, drying, thermoforming…

They are used in different sectors of the composite industry: aeronautics (helicopter blades, plane parts, ceramic matrix for engine…), yachting (hulls of boats…), electricity (tube for Very High Voltage isolators…), weaponry, spatial (tube for propulsive units…), transportation (overhead lines…), pharmaceuticals, chemicals (dental resin…), glass, rubber, cement, plastics, automotive, sport (bows, boards, skis…), wind turbine (blades), …

Because your process is unique, your oven is too. The experience acquired in the composite sector allows us to offer you ovens perfectly adapted to your requirements with a wide range of options and accessories. Do not hesitate to consult us.

Here few examples of our composite curing ovens:

The largest oven in Europe, 200°C class – 900m³ - 4 modules
Polymerization of composite hulls

• Internal dimensions: width 6,9 m x depth 32,6 m x height 4 m


• 200°C maxi


• Homogeneity: +/- 1,5°C at 180°C

Article on this oven

Modular oven XM 250 m³ – 8 modules
Polymerization of vacuum bagging composite parts

• Internal dimensions: width 4,4 m x depth 16,8 m x height 3,4 m


• 250°C maxi


• 3 vertical lift doors: at the front, at the rear, in the middle


• Polymerization using the whole volume of 250m³ or using independently 2 volumes of 125m³


• FE3000 supervision software


• Cooling extractors


• 32 vacuum ports


• 32 measurement ports


• 64 plugs for J thermocouples

Industrial oven 16100 L
Oven for the polymerization of honeycombs

• Internal dimensions: width 2100 mm x depth 3650 mm x height 2100 mm


• 300°C maxi


• FE3000 supervision software


• Exclusive ventilation system


• Cooling extractor


• Filtered air inlet


• 16 plugs for J thermocouples


• Provision of a special trolley for honeycombs

Modular oven XM 48m³ – 4 modules
Polymerization of composite parts in closed aluminum molds with rubber skin inside, for the manufacturing of ventilation ducts for planes

• Internal dimensions: width 3 m x depth 8 m x height 2 m


• 250°C maxi


• FE3000 supervision software


• Cooling extractors

Modular oven XM 58m³ – 4 modules
Polymerization of glue for assembly of parts maintained at pressure

• Internal dimensions: width 3,3 m x depth 8 m x height 2,2 m


• 200°C maxi


• FE3000 supervision software


• 24 plugs for T thermocouples


• 6 vacuum ports


• 6 measurement ports


• 6 pressure ports


• Cooling extractors

Industrial oven XXL04.5
Polymerization of vacuum bagging composite parts

• Internal dimensions: width 1500 mm x depth 2000 mm x height 1500 mm


• 250°C maxi


• FE3000 supervision software


• 8 plugs for J thermocouples


• 2 vacuum ports


• 2 measurement ports

Top loading oven XTOP 4900L
Polymerization of parts by filament winding

• Internal dimensions: width 3500 mm x depth 1000 mm x height 1400 mm


• 200°C maxi


• FE3000 supervision software


• Drive system for mandrels rotation, with rotation detection system


• Activated carbon filtration of exhaust air


• Door opening assisted by electric cylinders

Top loading oven XTOP 14m³
Polymerization of composite parts placed in a mould

• Internal dimensions: width 8200 mm x depth 1200 mm x height 1400 mm


• 200°C maxi


• 12 plugs for K thermocouples


• Positioning guide inside the oven


• Door opening assisted by electric cylinders

Industrial oven XXL01
Polymerization of composite parts

• High-performance composite


• Internal dimensions: width 1000 mm x depth 1000 mm x height 1000 mm


• 200°C maxi


• Cooling extractor

Consult other examples of special composite curing ovens in the section Special ovens -> Composite.

Contact us at +33 1 64 21 30 60 for more information.